| Spindle speed 15,000 rpm,
200Nm |
Motor spindle speedMASTER® HSK-A63
Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp)
Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty
cycle) |
| NC swivel rotary table |
Swivel Rotary Table for simultaneous machining
Clamping surface dia. 630 x 500mm / 24.8 x 19.6 in swivel range -35 to
+110°, rotary axis 360° including direct measuring system for B- and
C-axis and working plane transformation |
| Tool magazine 60 pockets |
Tool magazine 60 places HSK-A63 Vertical chain
with double gripper incl. set up station for tool loading |
| Swarf conveyor, with cleaned slot
screen |
Swarf conveyor, scraper type with cleaned slot
screen |
| Internal coolant supply 40bar/600l |
Internal coolant supply (ICS) with paper type
filter, 40 bar/23 l/min / 600-l tank 580 psi/6 gallon/min /160 gallon
incl. cabin roof, rotary joint in spindle, double cartridge filter
50µm for internal coolant (differently from standard) |
| Coolant-air blast change-over |
Coolant - Air-blast changeover external switchable
via M-Function |
| Air blast through spindle centre |
Air blast through spindle centre activated by M
function, maintained air with low oil rate |
| Chip flushing for working area |
Chip flushing for working area rinsing line on the
right side panel, backside of machine bed, cabin left and right
activated or deactivate by M function´s (only in combination with
internal coolant supply, not with 20 bar ICS) |
| Double cartridge filter, 25 µm |
Double cartridge filter, Finesse of filtration 25
µm, manually reversible (only in connection with separate paper-type
filter) |
| Rotating clear-view window |
Rotating clear-view window (only available with
option cabin roof) |
| Oil- and emulsion mist separator
mechanical |
Oil and emulsion mist separator mechanical filter
system 1100 m³/h (only available with option cabin roof) |
| Infrared measuring probe TS460 |
Infrared touch probe make Heidenhain TS 460 |
| Laser tool measuring BLUM DIGILOG |
Laser tool measuring Blum DIGILOG fix mounted at
machine column modified construction, note interference contour! Tool
lenght and diameter measuring automatically cleaning through external
airblast Calibration tool with taper |
| 3D Quick SET |
3D quickSET Tool kit for control and compensation
of the cinematic accuracy of 5 axis machine configurations (only with
option touch probe) |
| MPC Machine Protection Control |
MPC Machine Protection Control Machine protection
by quick shutdown |
| Signal lamp 4-colour |
Signal lamp 4 colour Red: general error Yellow:
intervention necessary Green: automatic mode Blue: set-up mode |
| proTIME |
proTIME Visualisation of remaining runtime,
remaining workpieces and the machine state |
| Door drive for working area door |
Door drive for working area door electrical door
drive, Open / close - activated by two-hand-operation at the control
panel Safety sensor technology for prevention of accidents Remark: Not
usable for automation! |
| Standard Automation
Interface |
Automation interface according to DECKEL MAHO
Standard consisting of: Interface (Profibus) via M65 Automatic loading
door Working table with 4-channel rotary joint |
| Active chiller for speedMASTER®
spindle |
Active chiller speedMASTER® for raised cooling
efficiency of main spindle drive / motor spindle |
| Exhibition design DMU50 3rd
generation |
Exhibition design DMU 50 3rd chiller of electrical
cabinet painted in electrical cabinet color; lighting of tool
magazine; DMG-MORI set of labels; paper version of electrical
plan |
| Application Tuning Cycle ATC |
Application Tuning Cycle ATC programmable feed
parameter selection for machining task: accuracy/surface/speed |
| One free M-function |
One free M-function M20 potential-free on contact
inside electrical cabinet |
| Safety package for power failure (incl.
IPC) |
Safety package for power failure: Package for
power failure IPC CELOS (for proper shutdown of IPC); Overload
limiter, Undervoltage monitoring with fast deceleration control |
| Operation mode 4 |
Operation mode 4 Process monitoring in the
production Manual intervention with open doors of machining area.
Release after check list has been filled in. |
| Accessories (internal handling) - RMS
Sensor |
Accessories (internal handling) |
|
|
| Digital Manufacturing Package |
Digital Manufacturing Package (1) IoTconnector
Allows the use of the Online services from DMG MORI (2) Machine Data
Connector (MDC) Standardized machine data interface Protocols: OPCUA,
MTConnect, MQTT (3) NETservice Qualified support through
internet-b |
| Messenger V4 |
The latest version of DMG MORI Messenger displays
web based the machine live status. It allows to analyze the machine
run-time, downtime, alarms in individually configurable dashboards
and transparently shows the actual status in the manufacturing
shop |
| Service Agent |
Service Agent Overview of all maintenance work on
the machine |
| Special equipment |
S-H3112 CAD Import: Opening CAD files directly on
the TNC 640/TNC7. |